Go Back   American Expedition Vehicles - Product Forums > AEV For Sale > Parts For Sale

Reply
Thread Tools Display Modes
  #1  
Unread 10-16-2016, 01:11 PM
ERAUGrad04's Avatar
ERAUGrad04 ERAUGrad04 is offline
Member
 
Join Date: Jun 2014
Posts: 83
Default Complete Dynatrac ProRock44 - Avail Jan 2017

Hi all!

I will be swapping axles at the end of the year, and I wanted to start a thread to see if there is any interest in my ProRock 44. If everything goes according to plan, the axle should be available by mid-end of January and I will be more than happy to deliver within the Bay area. Once January rolls around, the axle will be approximately 16 months old and will have ~22,000mi on it.

The axle will be sold "complete," brake disk to brake disk, including the Synergy tie rod and PSC ram. Currently, the axle will need to have spring perches and shock mounts welded back on as they were removed for the EVO DTD setup. I will provide the brackets and we can work out getting them welded back on if necessary.

***Note: Being that this axle has a raised trackbar bracket and a flipped draglink, this axle is best for Jeeps with a minimum of 3" of lift. ***

Here is what is included:
  • Dynatrac ProRock44 Unlimted (10* of pinion/caster separation) with Extreme 1/2" thick tubes (*Note: I typically run 7.5* of caster as opposed to the OEM 4.2* and the extra 3*+ of caster makes a big difference for a daily driver.)
  • Synergy trackbar bracket with integrated hydro ram mounts
  • 5.13 gears
  • OEM Rubicon e-locker (plug and play w/ facotry locker wiring)
  • Dynatrac Prosteer ball joints
  • RCV axle shafts
  • 1350 yoke
  • OEM knuckes
  • OEM brake calipers, pads & disks
  • OEM unit bearings w/speed sensor wiring included
  • Synergy Tie Rod w/misalignment boots
  • 6-1/2" PSC Ram
  • OEM flipped draglink (RHD draglink)
  • EVO Lower Control Arm Mount skids


Here is the best shot I've currently got of the axle. I can easily grab more if there is something specific someone wants to see.



Asking price is $3250

Thanks for looking!
-ERAU

Last edited by ERAUGrad04; 11-22-2016 at 09:12 PM.
Reply With Quote
  #2  
Unread 10-21-2016, 09:51 PM
ERAUGrad04's Avatar
ERAUGrad04 ERAUGrad04 is offline
Member
 
Join Date: Jun 2014
Posts: 83
Default

Price dropped to $4250!
Reply With Quote
  #3  
Unread 10-24-2016, 06:38 PM
bbusch bbusch is offline
Junior Member
 
Join Date: Feb 2013
Location: Incline Village, NV Lake Tahoe
Posts: 13
Default

What is the width of the axle?
__________________
03 Black Rubicon

05 Rubicon Sahara #364
Reply With Quote
  #4  
Unread 10-25-2016, 07:40 PM
bbusch bbusch is offline
Junior Member
 
Join Date: Feb 2013
Location: Incline Village, NV Lake Tahoe
Posts: 13
Default

Also what is the bolt pattern?
__________________
03 Black Rubicon

05 Rubicon Sahara #364
Reply With Quote
  #5  
Unread 10-27-2016, 08:52 AM
ERAUGrad04's Avatar
ERAUGrad04 ERAUGrad04 is offline
Member
 
Join Date: Jun 2014
Posts: 83
Default

Quote:
Originally Posted by bbusch View Post
What is the width of the axle?
Quote:
Originally Posted by bbusch View Post
Also what is the bolt pattern?
Just responded to the PM, however, for everyone else, the axle is stock width (65.5" I belive) with the 5 on 5 bolt patterns.
Reply With Quote
  #6  
Unread 11-22-2016, 09:11 PM
ERAUGrad04's Avatar
ERAUGrad04 ERAUGrad04 is offline
Member
 
Join Date: Jun 2014
Posts: 83
Default

Friendly bump with a price drop!

While doing a routine oil diff service, I found a small chip in the front ring gear. I was going to have a new ring & pinion installed, however, there is a good possibility somebody might be interested in a different gear ratio.

Rather than having new gears installed, I am thinking of just lower the price significantly and leaving it as is. This would allow the buyer to install whatever ratio they'd prefer.

With this in mind, the new price is $3250.

Thanks for looking!
-ERAU
Reply With Quote
  #7  
Unread 11-23-2016, 08:08 AM
Ben Hedrick Ben Hedrick is offline
Senior Member
 
Join Date: Feb 2009
Location: Ormond Beach, FL (Wish I was out west)
Posts: 1,893
Default

I see you're from Embry–Riddle Aeronautical University but where are you and the axle located now?

Ben
__________________
Ben Hedrick
www.BenHedrick.com
HEDRICK Speedsports
2007 5.7L HEMI Sahara Unlimited - Sold
2010 6.1L HEMI Rubicon Unlimited - Sold
2011 6.4L (392) HEMI Rubicon Unlimited - Sold
2002 4.0L AEV Brute - Sold
2003 6.4L "Stroker" HEMI AEV Brute - Sold
2005 4.0L SC AEV K9 Brute
2014 345 HEMI Rubicon Xpo Adventurer
2000 4.0L AEV 112 Long Wheelbase
2006 4.0L AEV Brute Rubicon
Reply With Quote
  #8  
Unread 11-23-2016, 07:32 PM
ERAUGrad04's Avatar
ERAUGrad04 ERAUGrad04 is offline
Member
 
Join Date: Jun 2014
Posts: 83
Default

Hi Ben!

Currently out in San Fran. Familiar with Riddle?
Reply With Quote
  #9  
Unread 11-24-2016, 05:35 AM
Ben Hedrick Ben Hedrick is offline
Senior Member
 
Join Date: Feb 2009
Location: Ormond Beach, FL (Wish I was out west)
Posts: 1,893
Default

Quote:
Originally Posted by ERAUGrad04 View Post
Hi Ben!

Currently out in San Fran. Familiar with Riddle?
I live in Ormond Beach just north of the school in Daytona Beach and we also own an Aviation Securities company. Did you got to the Daytona school?

Ben
__________________
Ben Hedrick
www.BenHedrick.com
HEDRICK Speedsports
2007 5.7L HEMI Sahara Unlimited - Sold
2010 6.1L HEMI Rubicon Unlimited - Sold
2011 6.4L (392) HEMI Rubicon Unlimited - Sold
2002 4.0L AEV Brute - Sold
2003 6.4L "Stroker" HEMI AEV Brute - Sold
2005 4.0L SC AEV K9 Brute
2014 345 HEMI Rubicon Xpo Adventurer
2000 4.0L AEV 112 Long Wheelbase
2006 4.0L AEV Brute Rubicon
Reply With Quote
  #10  
Unread 12-02-2016, 11:59 PM
ERAUGrad04's Avatar
ERAUGrad04 ERAUGrad04 is offline
Member
 
Join Date: Jun 2014
Posts: 83
Default

Quote:
Originally Posted by Ben Hedrick View Post
I live in Ormond Beach just north of the school in Daytona Beach and we also own an Aviation Securities company. Did you got to the Daytona school?

Ben
I went to the campus in Prescott, AZ. Only visited Daytona a few times. Completely different setting that what I was use to in AZ!
Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off
Forum Jump


All times are GMT -6. The time now is 02:50 PM.


Powered by vBulletin® Version 3.7.2
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.